RECTEQ RT-700 Wood Pellet Grill Manual
Download PDF assembly and user manual for recteq (Rec Tec) RT-700 Wood Pellet Grill (EN) 31 pages 2021 zip
Description
This PDF assembly and user manual is for the recteq / Rec Tec RT-700 Wood Pellet Grill.
recteq (Rec Tec) RT-700 Wood Pellet Grill
Please review the following information carefully for useful tips and information that will help you utilize your grill’s extensive features and benefits.
(PDF) ASSEMBLY MANUAL AND USERS GUIDE in English (EN) language.
CONTENTS:
– Important Safety Information
– Assembly Manual and Users Guide
– RT-700 Contents
– RT-700 Hardware
– RT-700 Assembly:
Step 1: Unpack and Prepare for Assembly
Step 2: Flip Grill and Attach Legs
Step 3: Install Left Leg Support Bracket
Step 4: Install Bottom Shelf and Right Leg Bracket
Step 5: Prepare for Side Shelf and Pull Bar Assembly
Step 6: Install Side Shelf
Step 7: Install RTD Wires to Smart Grill Technology(TM) Controller
Step 8: Install Pull Bar Handle
Step 9: Stand Grill Upright
Step 10: Install Bull Horn Handles
Step 11: Install Smokestack
Step 12: Heat Deflector, Drip Pan, Cooking Grates, and Drip Bucket
– RT-700 Competition Cart Assembly
– Initial Setup Procedure
– Operating Your Grill. Power Button. WIFI. Temperature Control Knob. Additional Temperature settings. LO. FUL. Settings Button.
– Adjustable Parameters, Probe A/B Calibration, Reset
– Test Mode
– Shutting Off Grill
– Tips, Tricks, and Temps. Preheating. Pellet Information.
– Operating Temperatures:
Smoking – 180°F to 275°F
Roasting/Braising – 275°F to 325°F
Baking – 325°F to 375°F
Grilling – 375°F to 450°F
Searing – 450°F+
– Maintenance & Cleaning
– Troubleshooting.
Please consult the Issue/Potential Cause/Solution chart in this user guide to help resolve issues you may encounter.
Issues:
– Grill will not light/turn on
– Grill is smoking excessively/smoke is discolored
– Grill will not heat up to or maintain proper temp
– Fire continues to go out
– Pellets are not being delivered to fire pot
– Flare ups
– Excessive grease/build up
– Smoke coming from hopper
– ER-1
– ER-2
– ER-3
In case of igniter failure, you can start your RT-700 manually:
1. Remove the stainless steel grates, drip pan, and heat deflector.
2. Clean out fire pot and place no more than 1/2 cup of pellets in the bottom. Add a small amount of solid fuel fire starter, such as those made from sawdust and wax, or use wood shavings.
Tip: A paper towel, shredded cardboard, or shredded newspaper can work as a substitute.
If you have a torch lighter, a fire starter is not needed.
3. Light the fire starter.
4. After the pellets are burning briskly, turn on your grill. If your fire goes out, repeat steps 1-4.
5. If your fire stays lit, replace the stainless heat deflector, drip pan, and cooking grates then close the lid.
– Controller Schematic
– Warranty
This assembly/user manual provides all the information (according to the table of contents) from recteq / Rec Tec about the RT-700 Wood Pellet Grill, including answers to the questions listed above. You can download and save it for offline use, including viewing it on your device or printing it for your convenience if you prefer a paper version.
Download it by clicking the button below
Helped you out?
Glad to hear that. It would be awesome if you could . . .
