Keurig K-Supreme Single Serve Coffee Maker Use and Care Guide

Download User Manual PDF for Keurig K-Supreme Single Serve Coffee Maker (Brewer) (EN) 7 pages DC0000006047 REV A 2020 zip



This PDF user manual is for the Keurig K-Supreme Single Serve Coffee Maker.

Keurig K-Supreme Single Serve Coffee Maker

Get the most from your new Keurig® K-Supreme brewer.

(PDF) USE & CARE GUIDE in English (EN) language.


– Plug & Place: Remove packing tape from brewer. Plug into a grounded outlet. Place a large mug (10oz minimum) on the drip tray.
– Rinse & Fill: Remove the water reservoir lid, then lift the reservoir straight up to remove it. If you have a Keurig® Water Filter, install it now. Refer to your Water Filter Starter Kit for instructions. Rinse reservoir with fresh water and fill to the MAX FILL line. Replace water reservoir. Replace lid.
– Lift & Lower: Lift and lower the handle. Do not insert a K-Cup® pod. The brewer will power on automatically.
– Cleansing Brew: The 4 cup sizes will blink. Press the 8oz button, then press the blinking brew button to start a cleansing brew. Pour the hot water into the sink.
The one-time setup process is now complete and you are ready to brew!

BREW YOUR FIRST CUP. How to use the Keurig K-Supreme Single Serve Coffee Maker.
– Place Mug & Pod: Place a mug on the drip tray. If using a travel mug, remove the drip tray and place the mug on the drip tray base. Lift the handle and place a K-Cup® pod in the K-Cup® pod holder. Lower the handle completely to close the lid.
For bolder coffee press the STRONG button, followed by the brew button.
For iced beverages fill a large plastic tumbler with ice. Insert any K-Cup® pod, then press the OVER ICE button, followed by brew button.

– Brew & Enjoy! The 4 brew size buttons will blink. Select your brew size, then press the blinking brew button. For a stronger coffee, press the STRONG button before brewing. The brew button will remain illuminated while brewing. Brewing is complete when the buttons are no longer illuminated. Lift the handle and dispose of the K-Cup® pod.

– Brewer Features:
Smart Start heats then brews in one simple process. No need to wait for the brewer to heat before selecting brew size. Simply power on your brewer by lifting the handle, add a K-Cup® Pod, select your brew size, then press the brew button. The brewer will heat, then automatically begin brewing.
Auto Off automatically turns your brewer off 5 minutes after the last brew for energy savings.
High Altitude To ensure your brewer works properly at higher altitudes (5,000 feet), enable the High Altitude setting by pressing and holding the brew button and 8oz buttons for 3 seconds.
Strong Brew for a bolder, more intense cup. Over Ice brew your favorite beverages over ice.

– Flip Brewer Over: Remove the drip tray and the water tank and set them aside. On a flat surface, carefully turn the brewer over so the base is facing up. You will see two parts: the water tank base (Part B) and the locking tab (Part A).

– Remove Part A: Slide Part A out of the brewer. It should release freely with little resistance.

– Lift, Pivot Part B:
Next re-position part B.
1. Gently pull outward to disengage from the brewer.
2. Rotate upward, as shown above. Part B will remain attached to the brewer.
3. Part B should now pivot freely to the second position. Remember to move the power card, so it does not get caught.

– Insert B, Replace A: Replace Part B in its new position. Rotate downward so that B is parallel to the base, then slide B back into position. Remember to replace the power cord. Slide Part A back into the second position to lock B in place. Flip the brewer back upright. You are now ready to use your Keurig Brewer!

Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
– How to clean Brewer Exterior
– How to clean Water Reservoir
– How to empty and clean Drip Tray
– Regular Maintenance. Follow the recommended maintenance schedule (chart attached).
– How to remove and clean K-Cup® Pod Holder.
– How to clean the Exit Needle
– How to remove and wash the Funnel
– How to clean the Entrance Needles

DESCALING YOUR BREWER. How to descale your Keurig K-Supreme Single Serve Coffee Maker?
You should descale your brewer every 3 months, or when the descale notification turns on. Properly follow the descaling procedure.
Depending on the mineral content of your water, calcium deposits or scale may build up in your brewer faster, making it necessary to descale more often.
– Descaling Procedure (and what you’d need for that):
– STEP 1: Prepare the Brewer
– STEP 2: Descale the Brewer. How to activate Descale Mode?
– STEP 3: Fresh Water Rinse. How many times should I repeat this step to get the DESCALE notification turns off.


Grounds in Your Coffee
Grounds may have gathered in the exit or entrance needles and can be cleaned using a straightened paper clip or similar tool.
– Clean the exit needle of the K-Cup® pod holder. Refer to the Exit Needle care instructions.
– Clean the brewer entrance needles. Refer to the Entrance Needles care instructions.

Brewer Will Not Brew
– A minimum of 6oz of water is required to brew. Add an additional 2oz of water to the reservoir to ensure the minimum fill level has been met, then press the brew button. Repeat until the brewer begins to dispense.

Brewing a Partial Cup
– Power the brewer off. Press and hold the brew button and 12oz button for 5 seconds until water starts dispensing. Then release and let the water purge. Discard the contents into the sink. Press the power button to restart.
– The exit needle may be clogged. Refer to the Exit Needle care instructions.
– Clean the K-Cup® Pod Holder, see K-Cup® Pod Holder care instructions.
– The brewer may need to be descaled. If you have repeated the descale procedure on your brewer two times and it is still only brewing a partial cup, contact Customer Service.

Brewer Does Not Have Power or Shuts Off
– Make sure that the power button has been turned on.
– Plug brewer into its own grounded outlet. If the electric circuit is overloaded with other appliances, your brewer may not function properly. The brewer should be operated on its own circuit, separate from other appliances.
– For energy savings, the brewer automatically turns off 5 minutes after the last brew. Press the power button to restart.
– If the brewer still doesn’t have power, contact Customer Service.

HELPFUL HINTS. What kind of water is recommended for brewing coffee? Is destilled water can be used for brewing coffee?
Water quality varies greatly. If you notice an undesirable taste in your beverage (such as chlorine or mineral tastes), we recommend using bottled or filtered water. Do not use distilled water.

Beyond these recommended cleaning and maintenance procedures, this brewer is not user serviceable. For service, please refer to the Warranty section of this guide.

Empty the water reservoir before storing or transporting and take care to ensure that you store your brewer in a safe and frost-free environment. When you prepare to use it after storage, we recommend rinsing the water reservoir with fresh water and descaling the brewer as detailed in the Descaling your Brewer section.
If you plan to move your brewer to a different location, turn the brewer off, unplug it, and empty the water reservoir.
If your brewer has been in an environment below freezing, please be sure to let it warm to room temperature for at least 2 hours before using.

WARRANTY. What is not covered by the limited warranty? Other limitations. How do you obtain warranty service?


This Keurig K-Supreme Single Serve Coffee Maker user manual is very helpful and can answer most of your questions about your coffee maker, including how to use it and how to troubleshoot common problems.

This use and care guide provides all the information (according to the table of contents) from Keurig about the K-Supreme Single Serve Coffee Maker, including answers to the questions listed above. You can download and save it for offline use, including viewing it on your device or printing it for your convenience if you prefer a paper version.

Download it by clicking the button below

Helped you out?
Glad to hear that. It would be awesome if you could . . .